Failover failed when customize the IP address for the VM
Dear Friends, The failover testing is successful, but the failover failed when the below errors. Could you help to find the work round? thanks. SRM 4.1 vCenter 4.1 IBM DS8700 Storage. [2013-03-24...
View ArticleSite Recovery Manager error "Cannot complete customization"
Site Recovery Manager v5.0.2.919478 error: "Cannot complete customization, possibly due to a scripting error or invalid script parameters (Error Code: -1). IP settings may have been partially applied"....
View ArticleI can not create a protection group because i don´t see the array pair
Hi I´m installing the Site Recovery Management 5.1 with vnx5300 EMC -NFS- but i cann´t create the protection group because when i try to create the protection group i can not select array pair because...
View ArticleReprotect with vSphere replication
Hello, We are using SRM 5.1 with vSphere replication. I'm trying to get a rough idea of how long a reprotect operation would take after a failover, in particular the synchronisation of storage. The...
View ArticleSite Recovery Manager issue, Reprotecting
I was able to setup SRM between 2 sites. I conducted a recovery to the DR site with 2 VM's.But when I tried to Reprotect them to the Production site it fails becuase i set it up as a VR protection...
View ArticleClik here to view.
VRM service keeps stopping
I am going through the intial config of setting up SRM. I have two vcenter servers and sites setup, and was able to deploy the VRMS server for the recovery site. However, on the source/protected...
View ArticleHow to figure out to which VM belongs RDM LUN when you know its naa?
Good dayI wonder is there any way to figure out to which VM belongs RDM LUN if I know its naa?Lets say that i'm observing some scsi errors in vmkernel.log. In that log i can only see the naa of the...
View ArticleSRM 5.1 not shows 'last sync completed , last sync duration ' for several...
I have a VMware 5.1, vcenter 5.1 insfrasturcure at both primary and DR site. I have replicate 12 VMs to DR site using SRM 5.1. But two VMs not show the "last sync completed" and "last sync duration"....
View ArticleClik here to view.
SRM 5.1 - Configure Connection "Could not be connected"
Hi All,I'm currently evaluating SRM 5.1I've gone through the installation as recommended by the installation guide and installed SRM and the Plugin at both the Protected and Remote site.I've moved onto...
View ArticleHow many IP's are required to set up replication on 25 vm's using SRM?
Hi All, I am new to SRM. We are using vsphere based replication. There are 25 vm's are running. My doubt is how many ip's are required to set up replication on all 25 vm's? Durga. Greatly appreciated.
View ArticleInvalid State - Local VRMS server Disconnected
Hello I'm in the process of setting up SRM 5.1 and I'm up to the stage where I just Deploy VR Appliance. Everything is fine until I click on Configure VR Appliance. The Error Message pops up "Invalid...
View ArticleSRM Hypervisor Replication Requirments
Hello, We're currently looking at implementing a SRM solution between or Production and DR sites. Currently in our VMware 5.1 environment our ESXi clusters are hooked up to an IBM XIV Gen II via 8GB...
View ArticleSRM in a single site
Hi, The give away is probably in the name but is it possible to use SRM in a single site. Our configuration is that we have one site but we have a cluster for DR, it is located in a different building....
View ArticleRe: SRM Replication
Hello Guys, I have a Scenario and i need some solution for this. We dont have SRM in place right now. We have two virtual machines with huge capacity say around 3TB shared across different luns(SAN) ....
View ArticleSelf-signed certificate installed successfully but with error VR appliance
HI Gurus, I am in the middle of upgrading SRM 5 to SRM 5.1 for vSphere replication. I am trying install and register the VR appliance 5.1. On the configuration tab I have populated the info: and tried...
View ArticleDownloading Older SRAs
Hi, I have a site which has been running SRM 4.0 using array based replication on IBM DS4700 arrays. I'm now attempting to update both sites to vSphere 5.x and SRM 5.x. The DS4700s have been upgraded...
View ArticleSRM Licensing
Hi, I am going to purchase Vmware SRM product for my DR site. But i dont have an idea about the number of items need to be purchased. Do i have to purchase 2 Nos of SRM(1 for each location)?. And also...
View ArticlevCenter Service Status - VR Management
Our vCenter Service Status is showing an error under VR Management. "Unable to retrieve health data from https://xx.xx.xx.xx:8080/service/hms/cgi/health.py" This error is pointing at the ip address of...
View ArticleReal failover problem with EVA8400
Hi, I'm running SRM 4.1.2-484598 with two EVA8400's and 4.1 hosts. During a 'real' failover test a couple of week ago the hosts running protected VMs became unresponsive during the failover of the...
View ArticleSRM API Java Issue
Hello, I'm trying to write a small java app talking to SRM.i was able to generate srm.jar from the WSDL. But....when i want to try the sample provided in the SDK, there is a class SrmServiceLocator...
View Article